天气表

搜索产品

Why One Ceramic Drawing Gets Three Different Quotes

Three suppliers quote the same ceramic drawing. The numbers come back spread by a factor of three, and every cover letter says the same thing: made to your drawing. The usual conclusion is that one shop is overcharging or another has misread the part. Usually neither is true. They are quoting three different objects, and the difference is invisible because a quotation compresses them into a single line.

There is no way to judge which of the three is the right one by comparing the totals. There is a way to do it by taking each quote apart into five blocks, because that is how the number was built in the first place. What follows is that breakdown, written for the person who has to explain the choice to a purchasing manager afterwards.

Custom zirconia ceramic structural parts made to customer drawings

A Quote Is Five Numbers Wearing One Coat

Every ceramic part price is assembled from material, tooling, machining time, inspection and yield. None of these behaves like the others: material scales roughly with the blank, tooling is a fixed sum divided by quantity, grinding time scales with the number of tight faces rather than the size of the part, inspection is a fixed step per lot, and yield is an assumption about how many parts survive sintering and finishing. A supplier who quotes low has not found a cheaper way to make the same thing — they have changed one or more of these five assumptions.

The practical consequence is that a quote cannot be compared until each supplier has stated all five. A one-line unit price is not a quote, it is a placeholder. Ask for the breakdown and the spread usually narrows by itself, because two of the three shops will turn out to be quoting a different grade or a different inspection scope.

Block One: Which Powder, and Who Certifies It

"Zirconia" is not a material specification. Within one supplier's own range the grades differ enough to change both the price and whether the part works: the Y8 grade sits at about 89 percent zirconia with bending strength from 950 MPa and toughness from 11 MPa·m0.5; white 3Y at about 94.5 percent with strength from 900 MPa and toughness from 10; the yellow grade at about 94 percent with 850 MPa and 8. Alumina is a different cost structure again. The material classification guide lays out the family, and the grade selection guide compares them on the properties that matter for a given duty.

The low quote often assumes a grade that meets no stated requirement on the drawing, because the drawing only said "zirconia". The high quote may include a lot-specific certificate with measured density and strength. Both are defensible; they are not the same purchase. The question to put to each supplier is which grade, which powder lot, and whether the certificate is per lot or a generic datasheet.

Block Two: Tooling, and Over How Many Parts It Is Spread

This is the block that most often produces a threefold spread on a small order. Injection moulding needs a tool; dry pressing needs a simpler one; machining from a sintered blank needs none. A supplier quoting CIM will either show tooling as a separate line or bury it in the unit price, and the arithmetic changes completely between 100 parts and 10,000.

Two quotes that look far apart at low volume frequently converge at production volume, and a purchasing decision made on the prototype quantity locks in the wrong route. Ask for tooling as a separate line, and ask for the unit price at two quantities — the trial batch and the expected annual volume. A shop that will only quote one quantity is telling you it has not thought about the ramp. The route itself is described under precision ceramic injection moulding and in the CIM manufacturing guide; the drawing-based custom part route is where this conversation normally starts.

Drawing-based machining, by contrast, carries no tool cost but consumes far more grinding time per piece. Precision-machined alumina structural parts are the usual example: the right answer for a handful of pieces and an expensive one for a production run.

Block Three: Grinding Hours — the Line That Moves Most

Sintering shrinks a ceramic part by roughly twenty percent and does not do it perfectly uniformly. Everything that has to be accurate afterwards is diamond-ground, and grinding is slow, skilled, and priced by the hour. This is where a tolerance callout turns into money.

The relationship is not linear. Holding one sealing face flat is a different job from holding a bore, an outer diameter and a shoulder concentric to each other. Reaching a cylindricity of 0.005 mm, a coaxiality of 0.01 mm or an Ra of 0.05 requires additional passes, additional setups and additional measurement between them. A quote built from a drawing where every dimension carries the same tight tolerance will be far higher than one where only the functional faces are tight — and a quote that is far lower usually means the supplier read the general tolerance block and ignored the tight callouts.

This is the single most useful question in the whole comparison: how many faces did you assume need grinding, and to what tolerance? Ask each supplier to list them. Two shops quoting the same part at very different levels almost always disagree here.

Precision machined zirconia ceramic structural parts

Block Four: Inspection Is a Cost, Not a Favour

Inspection does not appear as a separate line on most quotes, which makes it the easiest place to save money without anyone noticing until the parts arrive. The variables are what gets measured, on how many pieces, with which instrument, and whether a report is issued.

A serious quote names the method and the standard behind each figure — for example GB/T 6569-2006 for bending strength or GB/T 16534-2009 for Vickers hardness — and states whether critical dimensions are measured on every piece or sampled. A cheap quote frequently covers a visual check and a dimensional spot check only. For a part going into a regulated assembly, that difference is not a saving; it is a missing document that someone will ask for later. The plant-side view of what a proper quality system looks like is set out in the precision ceramic quality control article and the factory technology overview.

Ask specifically: which dimensions are measured, with what instrument, at what sampling rate, and will a report accompany the lot. If the answer is "we check everything" without numbers, that is not a specification.

Block Five: The Yield Assumption Nobody Writes Down

Ceramic parts are lost at several stages — during debinding, during sintering if a part warps, and during final grinding if a corner chips. The scrap rate is real cost, and it is built into the unit price as an assumption. A supplier quoting aggressively is often assuming a yield that a difficult geometry will not achieve; when the first batch underperforms, the price is revised or the delivery slips.

The geometry drives this more than the material. Thin walls, blind holes, sharp internal corners and a large flat face all raise the risk. A drawing that was originally a metal part is the worst case, because it carries features that ceramic cannot be ground to without a high rejection rate; that is a design issue, not a supplier one. Ask what yield was assumed and whether the quoted price holds if the first article requires a process adjustment. Suppliers working from a drawing through an OEM and ODM programme will normally discuss this before the tool is cut.

A Comparison Sheet You Can Actually Use

Cost block What a low quote usually assumes What a high quote usually includes The question that exposes it
MaterialGeneric zirconia, generic datasheetNamed grade, per-lot certificateWhich grade, which lot, whose certificate?
ToolingNo tool, or amortised over a large assumed volumeTool listed separately, priced at the real batch sizeShow tooling separately; quote trial and annual volumes
GrindingGeneral tolerance applied to all facesTight faces ground in dedicated setupsList the faces you assumed need grinding
InspectionVisual and spot dimensional check, no reportNamed methods, sampling rate, measured reportWhich dimensions, which instrument, how many pieces?
YieldOptimistic scrap rate, no first-article allowanceScrap priced in, first article validatedWhat yield was assumed, and does the price hold after the first article?

Fill this in for all three quotes before discussing the total. In most cases the comparison resolves itself: one supplier is not cheaper, they have simply left out two rows.

Precision machined alumina ceramic components

Three Ways a Cheap Quote Becomes an Expensive One

The tolerance block is copied from a metal drawing. A blanket tolerance across every surface multiplies grinding hours, and a supplier who quoted against the general block will come back for a revision once the tight callouts are noticed. Mark the functional faces explicitly and let the rest sit at a general tolerance; the saving is real and it belongs to the buyer, not the shop.

The inspection scope is undefined. "Meets drawing" is not a deliverable. If the assembly later needs a measured report for incoming goods, producing it after the fact means either re-measuring the lot or having no record at all. This is the most common source of a rejected first shipment.

Tooling is hidden in the unit price. It looks attractive on a trial order and becomes expensive on every subsequent batch, because the buyer never learns the tool has already been paid for. A separate tooling line is the only structure that lets a price come down as volume rises.

There is a broader version of this problem in supplier selection generally — the guide to choosing a ceramics factory for custom components covers the qualification side — but the specific discipline here is narrower: never compare totals, always compare the five blocks.

What to Send So the Three Quotes Are Comparable

The spread usually shrinks before any negotiation, once the enquiry itself stops leaving room for interpretation. Six items do it:

Named material grade, not a family name, plus whether a per-lot certificate is required.

Two quantities — trial batch and expected annual volume — with tooling requested as a separate line.

Tolerances assigned face by face, with datum surfaces named and a general tolerance for everything else.

Surface finish where it functions, stated as an Ra limit on specific faces only.

Inspection scope and documents — which dimensions, sampling rate, and whether a report ships with the lot.

The intended assembly and duty, since it determines which of the tolerances are actually functional.

Send the same package to all three and ask each to return it with their assumptions filled in. At that point the totals can be compared honestly — and a supplier who declines to itemise has answered the question in a different way. Standard custom ceramic parts and drawing-based development can both be quoted against this list.

Send the drawing and the two quantities — we will return an itemised quote.

获取完整报价

Please write a email.